{"title":"Ogee (F-Profile)","description":null,"products":[{"product_id":"vincent-ogee-profile-wheel-continuous-prof-f30-dm-120-35-35-p4-epic-resin","title":"Vincent F30 Epic CNC Profile Wheel – Position 4 Polishing","description":"\u003cp\u003eThe Vincent F30 EPIC CNC profile wheel is a 4.72 in. (120 mm) position 4 resin polishing wheel that takes a CNC-profiled edge to gloss on granite, marble, engineered stone and ultra-compact \/ porcelain surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpindle speed:\u003c\/strong\u003e 2,700 RPM\u003cbr\u003e\n\u003cstrong\u003eFeed rate:\u003c\/strong\u003e up to 59 in.\/min (1,500 mm\/min)\u003cbr\u003e\n\u003cstrong\u003eStock removal:\u003c\/strong\u003e zero — this wheel refines, it does not cut\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 4.72 in. (120 mm) · \u003cstrong\u003eHeight:\u003c\/strong\u003e 1.38 in. (35 mm) · \u003cstrong\u003eBore:\u003c\/strong\u003e 1.38 in. (35 mm)\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePosition 4 of Vincent's 0–6 set: positions 0–3 are metal bond and cut, positions 4–6 are resin and refine. This one removes no stock at all — that is why it can leave the cleanest edge the set is capable of.\u003c\/li\u003e\n\u003cli\u003eEPIC resin replaces Vincent's earlier three-step WINNER polish. Vincent publishes three times the life of WINNER and a resin layer thick and uniform enough to hold a consistent polish from the first piece to the last without dropping to reduced starting parameters.\u003c\/li\u003e\n\u003cli\u003eRun at 2,700 RPM with a feed of up to 59 in.\/min (1,500 mm\/min). Stock removal is zero by design: the wheel refines the surface the position 3 metal wheel left rather than cutting it further.\u003c\/li\u003e\n\u003cli\u003eFinished off the machine. Where the set is dimensionally matched and the polish positions are programmed in sequence, the edge comes off the CNC ready to ship rather than going to a bench for hand polishing.\u003c\/li\u003e\n\u003cli\u003eFitment: 4.72 in. (120 mm) diameter, 1.38 in. (35 mm) working height, 1.38 in. (35 mm) bore. Vincent sizes its resin polishers to match the metals in the same set, so positions swap without re-setting the tool length.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWho Is This For\u003c\/h3\u003e\n\u003cp\u003eA high-production shop that wants to polish straight off the CNC. The reason to run the full 4–6 resin sequence rather than stopping at position 5 is that each wheel is cutting finer than the last with zero stock removal, so the edge geometry set by the metals is preserved while the surface is brought up — no secondary polishing, no hand blending, and no operator standing at the machine during unattended cycles.\u003c\/p\u003e\n\u003cp\u003eIt is not a stock-removal tool and will not correct a bad edge. If the profile still shows tooling marks, the fault is upstream: go back to the position 3 fine metal wheel in the same F30 set and re-cut, then polish. Running a resin polisher harder to fix a metal-wheel problem only burns the resin.\u003c\/p\u003e\n\u003cp\u003eVincent lists the EPIC resin line for polishing granite, marble, engineered stone and ultra-compact \/ porcelain materials, which is a wider range than the metal wheels it follows. The metals ahead of it in the set are the ones that have to match the material.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat feed rate and spindle speed should I run at position 4?\u003c\/strong\u003e\u003cbr\u003e\nVincent publishes up to 59 in.\/min (1,500 mm\/min) at 2,700 RPM for a position 4 polishing wheel of this type, with stock removal zero — this wheel refines, it does not cut. Those are the manufacturer's figures for the position, not a shop rule of thumb.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes this wheel remove any material?\u003c\/strong\u003e\u003cbr\u003e\nNo. Vincent publishes zero stock removal for the resin polishing positions. It refines the surface the metal wheels left; it does not change the profile.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I still need to hand polish after this?\u003c\/strong\u003e\u003cbr\u003e\nThat is the point of the resin set: Vincent's stated aim for its CNC polishing wheels is a finish that needs no additional hand buffing. Position 6 is the last wheel in the sequence, so the edge is finished off the machine.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat bore does it need?\u003c\/strong\u003e\u003cbr\u003e\n1.38 in. (35 mm). That is the standard Vincent profile-wheel spindle fitting for this range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs \"engineered stone\" the same as quartz?\u003c\/strong\u003e\u003cbr\u003e\nYes — engineered stone is Vincent's catalogue wording for quartz surfaces such as Caesarstone, Silestone and Cambria. The wheel is listed for them.\u003c\/p\u003e","brand":"Vincent","offers":[{"title":"Default Title","offer_id":52296599601372,"sku":"TYR 34578851","price":443.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0841\/5713\/7116\/files\/4ebb8a35-6363-44e4-8eb5-f455bf1fc0d6.png?v=1787088340"},{"product_id":"vincent-ogee-profile-wheel-continuous-prof-f30-dm-120-35-35-p5-epic-resin","title":"Vincent F30 Epic CNC Profile Wheel – Position 5 Polishing","description":"\u003cp\u003eThe Vincent F30 EPIC CNC profile wheel is a 4.72 in. (120 mm) position 5 resin polishing wheel that takes a CNC-profiled edge to gloss on granite, marble, engineered stone and ultra-compact \/ porcelain surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpindle speed:\u003c\/strong\u003e 2,700 RPM\u003cbr\u003e\n\u003cstrong\u003eFeed rate:\u003c\/strong\u003e up to 59 in.\/min (1,500 mm\/min)\u003cbr\u003e\n\u003cstrong\u003eStock removal:\u003c\/strong\u003e zero — this wheel refines, it does not cut\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 4.72 in. (120 mm) · \u003cstrong\u003eHeight:\u003c\/strong\u003e 1.38 in. (35 mm) · \u003cstrong\u003eBore:\u003c\/strong\u003e 1.38 in. (35 mm)\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePosition 5 of Vincent's 0–6 set: positions 0–3 are metal bond and cut, positions 4–6 are resin and refine. This one removes no stock at all — that is why it can leave the cleanest edge the set is capable of.\u003c\/li\u003e\n\u003cli\u003eEPIC resin replaces Vincent's earlier three-step WINNER polish. Vincent publishes three times the life of WINNER and a resin layer thick and uniform enough to hold a consistent polish from the first piece to the last without dropping to reduced starting parameters.\u003c\/li\u003e\n\u003cli\u003eRun at 2,700 RPM with a feed of up to 59 in.\/min (1,500 mm\/min). Stock removal is zero by design: the wheel refines the surface the position 3 metal wheel left rather than cutting it further.\u003c\/li\u003e\n\u003cli\u003eFinished off the machine. Where the set is dimensionally matched and the polish positions are programmed in sequence, the edge comes off the CNC ready to ship rather than going to a bench for hand polishing.\u003c\/li\u003e\n\u003cli\u003eFitment: 4.72 in. (120 mm) diameter, 1.38 in. (35 mm) working height, 1.38 in. (35 mm) bore. Vincent sizes its resin polishers to match the metals in the same set, so positions swap without re-setting the tool length.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWho Is This For\u003c\/h3\u003e\n\u003cp\u003eA high-production shop that wants to polish straight off the CNC. The reason to run the full 4–6 resin sequence rather than stopping at position 5 is that each wheel is cutting finer than the last with zero stock removal, so the edge geometry set by the metals is preserved while the surface is brought up — no secondary polishing, no hand blending, and no operator standing at the machine during unattended cycles.\u003c\/p\u003e\n\u003cp\u003eIt is not a stock-removal tool and will not correct a bad edge. If the profile still shows tooling marks, the fault is upstream: go back to the position 3 fine metal wheel in the same F30 set and re-cut, then polish. Running a resin polisher harder to fix a metal-wheel problem only burns the resin.\u003c\/p\u003e\n\u003cp\u003eVincent lists the EPIC resin line for polishing granite, marble, engineered stone and ultra-compact \/ porcelain materials, which is a wider range than the metal wheels it follows. The metals ahead of it in the set are the ones that have to match the material.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat feed rate and spindle speed should I run at position 5?\u003c\/strong\u003e\u003cbr\u003e\nVincent publishes up to 59 in.\/min (1,500 mm\/min) at 2,700 RPM for a position 5 polishing wheel of this type, with stock removal zero — this wheel refines, it does not cut. Those are the manufacturer's figures for the position, not a shop rule of thumb.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes this wheel remove any material?\u003c\/strong\u003e\u003cbr\u003e\nNo. Vincent publishes zero stock removal for the resin polishing positions. It refines the surface the metal wheels left; it does not change the profile.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I still need to hand polish after this?\u003c\/strong\u003e\u003cbr\u003e\nThat is the point of the resin set: Vincent's stated aim for its CNC polishing wheels is a finish that needs no additional hand buffing. Position 6 is the last wheel in the sequence, so the edge is finished off the machine.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat bore does it need?\u003c\/strong\u003e\u003cbr\u003e\n1.38 in. (35 mm). That is the standard Vincent profile-wheel spindle fitting for this range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs \"engineered stone\" the same as quartz?\u003c\/strong\u003e\u003cbr\u003e\nYes — engineered stone is Vincent's catalogue wording for quartz surfaces such as Caesarstone, Silestone and Cambria. The wheel is listed for them.\u003c\/p\u003e","brand":"Vincent","offers":[{"title":"Default Title","offer_id":52296599666908,"sku":"TYR 34578852","price":443.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0841\/5713\/7116\/files\/45aac6cb-66e5-44a4-88e6-1aab89433b19.png?v=1787088365"},{"product_id":"vincent-ogee-profile-wheel-continuous-prof-f30-dm-120-35-35-p6-epic-resin","title":"Vincent F30 Epic CNC Profile Wheel – Position 6 Polishing","description":"\u003cp\u003eThe Vincent F30 EPIC CNC profile wheel is a 4.72 in. (120 mm) position 6 resin polishing wheel that takes a CNC-profiled edge to gloss on granite, marble, engineered stone and ultra-compact \/ porcelain surfaces.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpindle speed:\u003c\/strong\u003e 2,700 RPM\u003cbr\u003e\n\u003cstrong\u003eFeed rate:\u003c\/strong\u003e up to 59 in.\/min (1,500 mm\/min)\u003cbr\u003e\n\u003cstrong\u003eStock removal:\u003c\/strong\u003e zero — this wheel refines, it does not cut\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 4.72 in. (120 mm) · \u003cstrong\u003eHeight:\u003c\/strong\u003e 1.38 in. (35 mm) · \u003cstrong\u003eBore:\u003c\/strong\u003e 1.38 in. (35 mm)\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePosition 6 of Vincent's 0–6 set: positions 0–3 are metal bond and cut, positions 4–6 are resin and refine. This one removes no stock at all — that is why it can leave the cleanest edge the set is capable of.\u003c\/li\u003e\n\u003cli\u003eEPIC resin replaces Vincent's earlier three-step WINNER polish. Vincent publishes three times the life of WINNER and a resin layer thick and uniform enough to hold a consistent polish from the first piece to the last without dropping to reduced starting parameters.\u003c\/li\u003e\n\u003cli\u003eRun at 2,700 RPM with a feed of up to 59 in.\/min (1,500 mm\/min). Stock removal is zero by design: the wheel refines the surface the position 3 metal wheel left rather than cutting it further.\u003c\/li\u003e\n\u003cli\u003eFinished off the machine. Where the set is dimensionally matched and the polish positions are programmed in sequence, the edge comes off the CNC ready to ship rather than going to a bench for hand polishing.\u003c\/li\u003e\n\u003cli\u003eFitment: 4.72 in. (120 mm) diameter, 1.38 in. (35 mm) working height, 1.38 in. (35 mm) bore. Vincent sizes its resin polishers to match the metals in the same set, so positions swap without re-setting the tool length.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWho Is This For\u003c\/h3\u003e\n\u003cp\u003eA high-production shop that wants to polish straight off the CNC. The reason to run the full 4–6 resin sequence rather than stopping at position 5 is that each wheel is cutting finer than the last with zero stock removal, so the edge geometry set by the metals is preserved while the surface is brought up — no secondary polishing, no hand blending, and no operator standing at the machine during unattended cycles.\u003c\/p\u003e\n\u003cp\u003eIt is not a stock-removal tool and will not correct a bad edge. If the profile still shows tooling marks, the fault is upstream: go back to the position 3 fine metal wheel in the same F30 set and re-cut, then polish. Running a resin polisher harder to fix a metal-wheel problem only burns the resin.\u003c\/p\u003e\n\u003cp\u003eVincent lists the EPIC resin line for polishing granite, marble, engineered stone and ultra-compact \/ porcelain materials, which is a wider range than the metal wheels it follows. The metals ahead of it in the set are the ones that have to match the material.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat feed rate and spindle speed should I run at position 6?\u003c\/strong\u003e\u003cbr\u003e\nVincent publishes up to 59 in.\/min (1,500 mm\/min) at 2,700 RPM for a position 6 polishing wheel of this type, with stock removal zero — this wheel refines, it does not cut. Those are the manufacturer's figures for the position, not a shop rule of thumb.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDoes this wheel remove any material?\u003c\/strong\u003e\u003cbr\u003e\nNo. Vincent publishes zero stock removal for the resin polishing positions. It refines the surface the metal wheels left; it does not change the profile.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I still need to hand polish after this?\u003c\/strong\u003e\u003cbr\u003e\nThat is the point of the resin set: Vincent's stated aim for its CNC polishing wheels is a finish that needs no additional hand buffing. Position 6 is the last wheel in the sequence, so the edge is finished off the machine.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat bore does it need?\u003c\/strong\u003e\u003cbr\u003e\n1.38 in. (35 mm). That is the standard Vincent profile-wheel spindle fitting for this range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs \"engineered stone\" the same as quartz?\u003c\/strong\u003e\u003cbr\u003e\nYes — engineered stone is Vincent's catalogue wording for quartz surfaces such as Caesarstone, Silestone and Cambria. The wheel is listed for them.\u003c\/p\u003e","brand":"Vincent","offers":[{"title":"Default Title","offer_id":52296599732444,"sku":"TYR 34578853","price":443.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0841\/5713\/7116\/files\/4786fdb7-de1a-483d-b331-811d7612adad.png?v=1787088403"},{"product_id":"vincent-ogee-profile-wheel-segmented-prof-f30-dm-140-35-35-p0-hs1-metallic","title":"Vincent F30 CNC Profile Wheel – Position 0 Segmented, 140 mm Diameter","description":"\u003cp\u003eThe Vincent F30 CNC profile wheel is a 5.51 in. (140 mm) position 0 segmented roughing wheel that takes the sawn edge down to the profile line on granite, engineered stone and natural quartzite before the shaping wheels run.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpindle speed:\u003c\/strong\u003e 4,800–5,500 RPM\u003cbr\u003e\n\u003cstrong\u003eFeed rate:\u003c\/strong\u003e up to 157 in.\/min (4,000 mm\/min)\u003cbr\u003e\n\u003cstrong\u003eStock removal:\u003c\/strong\u003e up to 0.020 in. (0.5 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 5.51 in. (140 mm) · \u003cstrong\u003eHeight:\u003c\/strong\u003e 1.38 in. (35 mm) · \u003cstrong\u003eBore:\u003c\/strong\u003e 1.38 in. (35 mm)\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSegmented rim for bulk removal — this is the first wheel in the set and the one that does the heavy cutting, not the one that sets the finish.\u003c\/li\u003e\n\u003cli\u003eVincent publishes up to 157 in.\/min (4,000 mm\/min) at 4,800–5,500 RPM for this position, with stock removal up to 0.020 in. (0.5 mm).\u003c\/li\u003e\n\u003cli\u003eThe softer bond releases spent diamond as it wears instead of polishing over, so the wheel keeps cutting without glazing on dense material such as quartzite and porcelain.\u003c\/li\u003e\n\u003cli\u003eFitment: 5.51 in. (140 mm) diameter, 1.38 in. (35 mm) working height, 1.38 in. (35 mm) bore. Vincent sizes its resin polishers to match the metals in the same set, so positions swap without re-setting the tool length.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWho Is This For\u003c\/h3\u003e\n\u003cp\u003eA high-production shop programming F30 edges on a CNC and running them in volume. At up to 157 in.\/min (4,000 mm\/min) this is a wheel built for unattended cycles and production throughput rather than one-off work.\u003c\/p\u003e\n\u003cp\u003eIt is not a polisher. Position 0 leaves a ground surface by design; the gloss comes from the position 4–6 resin polishers in the same F30 set. Do not try to close the surface by slowing this wheel down — that glazes the bond and shortens its life.\u003c\/p\u003e\n\u003cp\u003eVincent lists this wheel for granite, engineered stone and natural quartzite. For technical ceramics and Dekton it publishes a separate CERAM range; running a granite bond on ceramic slab is the usual cause of chipping at entry and exit.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat feed rate and spindle speed should I run at position 0?\u003c\/strong\u003e\u003cbr\u003e\nVincent publishes up to 157 in.\/min (4,000 mm\/min) at 4,800–5,500 RPM for a position 0 profiling wheel of this type, with stock removal up to 0.020 in. (0.5 mm). Those are the manufacturer's figures for the position, not a shop rule of thumb.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it polish the edge?\u003c\/strong\u003e\u003cbr\u003e\nNo — positions 0–3 are metal bond. They cut the profile; the resin positions 4–6 polish it. Expect a ground surface off this wheel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it hold up on quartzite and porcelain?\u003c\/strong\u003e\u003cbr\u003e\nThat is what the softer bond is for: it releases spent diamond rather than glazing, so the wheel keeps cutting on hard material. Vincent lists the range for granite, engineered stone and natural quartzite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat bore does it need?\u003c\/strong\u003e\u003cbr\u003e\n1.38 in. (35 mm). That is the standard Vincent profile-wheel spindle fitting for this range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs \"engineered stone\" the same as quartz?\u003c\/strong\u003e\u003cbr\u003e\nYes — engineered stone is Vincent's catalogue wording for quartz surfaces such as Caesarstone, Silestone and Cambria. The wheel is listed for them.\u003c\/p\u003e","brand":"Vincent","offers":[{"title":"Default Title","offer_id":52296614314204,"sku":"TYR 534033","price":1003.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0841\/5713\/7116\/files\/238bdbd4-ea9e-4403-8c78-174d3ec49690.png?v=1787089446"},{"product_id":"vincent-ogee-profile-wheel-continuous-prof-f30-dm-140-35-35-p1-hs1-metallic","title":"Vincent F30 CNC Profile Wheel – Position 1 Roughing, 140 mm Diameter","description":"\u003cp\u003eThe Vincent F30 CNC profile wheel is a 5.51 in. (140 mm) position 1 roughing metal-bond profiling wheel for shaping a CNC edge on granite, engineered stone and natural quartzite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpindle speed:\u003c\/strong\u003e 4,800–5,500 RPM\u003cbr\u003e\n\u003cstrong\u003eFeed rate:\u003c\/strong\u003e up to 197 in.\/min (5,000 mm\/min)\u003cbr\u003e\n\u003cstrong\u003eStock removal:\u003c\/strong\u003e up to 0.012 in. (0.3 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 5.51 in. (140 mm) · \u003cstrong\u003eHeight:\u003c\/strong\u003e 1.38 in. (35 mm) · \u003cstrong\u003eBore:\u003c\/strong\u003e 1.38 in. (35 mm)\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePosition 1 of Vincent's 0–6 set. Positions 0–3 are metal bond and take the edge to shape; positions 4–6 are resin and take it to gloss.\u003c\/li\u003e\n\u003cli\u003eVincent publishes up to 197 in.\/min (5,000 mm\/min) at 4,800–5,500 RPM for this position, with stock removal up to 0.012 in. (0.3 mm).\u003c\/li\u003e\n\u003cli\u003eThe softer bond releases spent diamond as it wears instead of polishing over, so the wheel keeps cutting without glazing on dense material such as quartzite and porcelain.\u003c\/li\u003e\n\u003cli\u003eFitment: 5.51 in. (140 mm) diameter, 1.38 in. (35 mm) working height, 1.38 in. (35 mm) bore. Vincent sizes its resin polishers to match the metals in the same set, so positions swap without re-setting the tool length.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWho Is This For\u003c\/h3\u003e\n\u003cp\u003eA high-production shop programming F30 edges on a CNC and running them in volume. At up to 197 in.\/min (5,000 mm\/min) this is a wheel built for unattended cycles and production throughput rather than one-off work.\u003c\/p\u003e\n\u003cp\u003eIt is not a polisher. Position 1 leaves a ground surface by design; the gloss comes from the position 4–6 resin polishers in the same F30 set. Do not try to close the surface by slowing this wheel down — that glazes the bond and shortens its life.\u003c\/p\u003e\n\u003cp\u003eVincent lists this wheel for granite, engineered stone and natural quartzite. For technical ceramics and Dekton it publishes a separate CERAM range; running a granite bond on ceramic slab is the usual cause of chipping at entry and exit.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat feed rate and spindle speed should I run at position 1?\u003c\/strong\u003e\u003cbr\u003e\nVincent publishes up to 197 in.\/min (5,000 mm\/min) at 4,800–5,500 RPM for a position 1 profiling wheel of this type, with stock removal up to 0.012 in. (0.3 mm). Those are the manufacturer's figures for the position, not a shop rule of thumb.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it polish the edge?\u003c\/strong\u003e\u003cbr\u003e\nNo — positions 0–3 are metal bond. They cut the profile; the resin positions 4–6 polish it. Expect a ground surface off this wheel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it hold up on quartzite and porcelain?\u003c\/strong\u003e\u003cbr\u003e\nThat is what the softer bond is for: it releases spent diamond rather than glazing, so the wheel keeps cutting on hard material. Vincent lists the range for granite, engineered stone and natural quartzite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat bore does it need?\u003c\/strong\u003e\u003cbr\u003e\n1.38 in. (35 mm). That is the standard Vincent profile-wheel spindle fitting for this range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs \"engineered stone\" the same as quartz?\u003c\/strong\u003e\u003cbr\u003e\nYes — engineered stone is Vincent's catalogue wording for quartz surfaces such as Caesarstone, Silestone and Cambria. The wheel is listed for them.\u003c\/p\u003e","brand":"Vincent","offers":[{"title":"Default Title","offer_id":52296614412508,"sku":"TYR 534034","price":970.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0841\/5713\/7116\/files\/62f673a7-6f6f-4945-9460-c34fd459e4ed.png?v=1787089467"},{"product_id":"vincent-ogee-profile-wheel-continuous-prof-f30-dm-140-35-35-p2-hs1-metallic","title":"Vincent F30 CNC Profile Wheel – Position 2 Medium, 140 mm Diameter","description":"\u003cp\u003eThe Vincent F30 CNC profile wheel is a 5.51 in. (140 mm) position 2 medium metal-bond profiling wheel for shaping a CNC edge on granite, engineered stone and natural quartzite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpindle speed:\u003c\/strong\u003e 4,800–5,500 RPM\u003cbr\u003e\n\u003cstrong\u003eFeed rate:\u003c\/strong\u003e up to 197 in.\/min (5,000 mm\/min)\u003cbr\u003e\n\u003cstrong\u003eStock removal:\u003c\/strong\u003e up to 0.008 in. (0.2 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 5.51 in. (140 mm) · \u003cstrong\u003eHeight:\u003c\/strong\u003e 1.38 in. (35 mm) · \u003cstrong\u003eBore:\u003c\/strong\u003e 1.38 in. (35 mm)\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePosition 2 of Vincent's 0–6 set. Positions 0–3 are metal bond and take the edge to shape; positions 4–6 are resin and take it to gloss.\u003c\/li\u003e\n\u003cli\u003eVincent publishes up to 197 in.\/min (5,000 mm\/min) at 4,800–5,500 RPM for this position, with stock removal up to 0.008 in. (0.2 mm).\u003c\/li\u003e\n\u003cli\u003eThe softer bond releases spent diamond as it wears instead of polishing over, so the wheel keeps cutting without glazing on dense material such as quartzite and porcelain.\u003c\/li\u003e\n\u003cli\u003eFitment: 5.51 in. (140 mm) diameter, 1.38 in. (35 mm) working height, 1.38 in. (35 mm) bore. Vincent sizes its resin polishers to match the metals in the same set, so positions swap without re-setting the tool length.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWho Is This For\u003c\/h3\u003e\n\u003cp\u003eA high-production shop programming F30 edges on a CNC and running them in volume. At up to 197 in.\/min (5,000 mm\/min) this is a wheel built for unattended cycles and production throughput rather than one-off work.\u003c\/p\u003e\n\u003cp\u003eIt is not a polisher. Position 2 leaves a ground surface by design; the gloss comes from the position 4–6 resin polishers in the same F30 set. Do not try to close the surface by slowing this wheel down — that glazes the bond and shortens its life.\u003c\/p\u003e\n\u003cp\u003eVincent lists this wheel for granite, engineered stone and natural quartzite. For technical ceramics and Dekton it publishes a separate CERAM range; running a granite bond on ceramic slab is the usual cause of chipping at entry and exit.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat feed rate and spindle speed should I run at position 2?\u003c\/strong\u003e\u003cbr\u003e\nVincent publishes up to 197 in.\/min (5,000 mm\/min) at 4,800–5,500 RPM for a position 2 profiling wheel of this type, with stock removal up to 0.008 in. (0.2 mm). Those are the manufacturer's figures for the position, not a shop rule of thumb.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it polish the edge?\u003c\/strong\u003e\u003cbr\u003e\nNo — positions 0–3 are metal bond. They cut the profile; the resin positions 4–6 polish it. Expect a ground surface off this wheel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it hold up on quartzite and porcelain?\u003c\/strong\u003e\u003cbr\u003e\nThat is what the softer bond is for: it releases spent diamond rather than glazing, so the wheel keeps cutting on hard material. Vincent lists the range for granite, engineered stone and natural quartzite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat bore does it need?\u003c\/strong\u003e\u003cbr\u003e\n1.38 in. (35 mm). That is the standard Vincent profile-wheel spindle fitting for this range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs \"engineered stone\" the same as quartz?\u003c\/strong\u003e\u003cbr\u003e\nYes — engineered stone is Vincent's catalogue wording for quartz surfaces such as Caesarstone, Silestone and Cambria. The wheel is listed for them.\u003c\/p\u003e","brand":"Vincent","offers":[{"title":"Default Title","offer_id":52296614609116,"sku":"TYR 534037","price":970.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0841\/5713\/7116\/files\/4780f822-35cb-4c1e-9927-562902094f48.png?v=1787089488"},{"product_id":"vincent-ogee-profile-wheel-continuous-prof-f30-dm-140-35-35-p3-hs1-metallic","title":"Vincent F30 CNC Profile Wheel – Position 3 Fine, 140 mm Diameter","description":"\u003cp\u003eThe Vincent F30 CNC profile wheel is a 5.51 in. (140 mm) position 3 fine metal-bond profiling wheel for shaping a CNC edge on granite, engineered stone and natural quartzite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpindle speed:\u003c\/strong\u003e 4,800 RPM\u003cbr\u003e\n\u003cstrong\u003eFeed rate:\u003c\/strong\u003e up to 98 in.\/min (2,500 mm\/min)\u003cbr\u003e\n\u003cstrong\u003eStock removal:\u003c\/strong\u003e up to 0.004 in. (0.1 mm)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 5.51 in. (140 mm) · \u003cstrong\u003eHeight:\u003c\/strong\u003e 1.38 in. (35 mm) · \u003cstrong\u003eBore:\u003c\/strong\u003e 1.38 in. (35 mm)\u003c\/p\u003e\n\u003ch3\u003eKey Features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003ePosition 3 of Vincent's 0–6 set. Positions 0–3 are metal bond and take the edge to shape; positions 4–6 are resin and take it to gloss.\u003c\/li\u003e\n\u003cli\u003eVincent publishes up to 98 in.\/min (2,500 mm\/min) at 4,800 RPM for this position, with stock removal up to 0.004 in. (0.1 mm).\u003c\/li\u003e\n\u003cli\u003eThe softer bond releases spent diamond as it wears instead of polishing over, so the wheel keeps cutting without glazing on dense material such as quartzite and porcelain.\u003c\/li\u003e\n\u003cli\u003eFitment: 5.51 in. (140 mm) diameter, 1.38 in. (35 mm) working height, 1.38 in. (35 mm) bore. Vincent sizes its resin polishers to match the metals in the same set, so positions swap without re-setting the tool length.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWho Is This For\u003c\/h3\u003e\n\u003cp\u003eA high-production shop programming F30 edges on a CNC and running them in volume. At up to 98 in.\/min (2,500 mm\/min) this is a wheel built for unattended cycles and production throughput rather than one-off work.\u003c\/p\u003e\n\u003cp\u003eIt is not a polisher. Position 3 leaves a ground surface by design; the gloss comes from the position 4–6 resin polishers in the same F30 set. Do not try to close the surface by slowing this wheel down — that glazes the bond and shortens its life.\u003c\/p\u003e\n\u003cp\u003eVincent lists this wheel for granite, engineered stone and natural quartzite. For technical ceramics and Dekton it publishes a separate CERAM range; running a granite bond on ceramic slab is the usual cause of chipping at entry and exit.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWhat feed rate and spindle speed should I run at position 3?\u003c\/strong\u003e\u003cbr\u003e\nVincent publishes up to 98 in.\/min (2,500 mm\/min) at 4,800 RPM for a position 3 profiling wheel of this type, with stock removal up to 0.004 in. (0.1 mm). Those are the manufacturer's figures for the position, not a shop rule of thumb.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it polish the edge?\u003c\/strong\u003e\u003cbr\u003e\nNo — positions 0–3 are metal bond. They cut the profile; the resin positions 4–6 polish it. Expect a ground surface off this wheel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill it hold up on quartzite and porcelain?\u003c\/strong\u003e\u003cbr\u003e\nThat is what the softer bond is for: it releases spent diamond rather than glazing, so the wheel keeps cutting on hard material. Vincent lists the range for granite, engineered stone and natural quartzite.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat bore does it need?\u003c\/strong\u003e\u003cbr\u003e\n1.38 in. (35 mm). That is the standard Vincent profile-wheel spindle fitting for this range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIs \"engineered stone\" the same as quartz?\u003c\/strong\u003e\u003cbr\u003e\nYes — engineered stone is Vincent's catalogue wording for quartz surfaces such as Caesarstone, Silestone and Cambria. The wheel is listed for them.\u003c\/p\u003e","brand":"Vincent","offers":[{"title":"Default Title","offer_id":52296650457308,"sku":"TYR 541201","price":970.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0841\/5713\/7116\/files\/e00fe1af-36ae-4c7f-9657-cd42ca01868e.png?v=1787091135"}],"url":"https:\/\/obsidian-industrial.com\/collections\/stone-fabrication-tools-cnc-tools-profiles-by-vincent-ogee-f-profile.oembed","provider":"Obsidian Industrial","version":"1.0","type":"link"}